Ceramic Thermal Spray Coatings

A pump seal that scores in weeks, a thread guide grooved by fiber, a shaft that needs electrical isolation: each of these failures starts at the surface. Ceramic thermal spray coatings answer them with a dense, hard oxide layer built onto the metal part itself, so the base component keeps its strength while the surface takes the abuse.

A&A Coatings has provided top-notch services for thermal spray coatings in South Plainfield, New Jersey, since 1944. Ceramics are one family within that niche. Below you will find how each oxide we spray performs, how to match one to your failure mode, and what happens to the part before and after the gun.

Robotic arm with spray nozzles applying ceramic thermal spray coatings

Problems that a Ceramic Coating Solves on Industrial Parts

Oxide ceramics earn their place where metals give out. They resist abrasive grains, hard mating surfaces, particle erosion and cavitation, and several grades hold up against acids and alkalis that would attack bare steel.

Their other advantage is electrical. Alumina-based coatings carry high dielectric strength, which lets an engineer insulate a conductive part without redesigning it in solid ceramic.

These are industrial coatings for machine elements, not the polymer car care products sold under the same “ceramic” name. For a shorter primer on the main groups, see our guide to the types of ceramic thermal spray coatings.

Oxide Ceramic Coating Materials A&A Sprays

A&A sprays eight oxide ceramic materials, and each has its own data page with powder composition, coating properties, thickness limits and finishing notes. The summaries here point you to the right one.

White Alumina and Premium Grade White Alumina

Our plasma white alumina is 98.5% aluminum oxide. It produces dense coatings that resist wear by fibers and threads and resist erosion at high temperatures, and it also works as a thermal barrier.

When sealed, white alumina provides electrical resistance at high temperatures. It is designed for thin coatings of no more than 0.020″ (0.5 mm), with a macrohardness of Rc60.

A premium grade white alumina coating starts from 99.5% pure fused aluminum oxide with a narrow particle size distribution. That powder feeds smoothly, so the coating sprays more uniform and smoother, at 110 to 150 microinches RMS as sprayed.

In abrasive slurry testing, premium grade coatings showed roughly 100% higher wear resistance than standard grade white alumina. Dielectric strength runs 450 to 500 volts per mil, which makes this grade a strong choice for electronic components, pump seals and low-friction contact with fibers.

Alumina-Titania and Nano Alumina-Titania

Adding 13% titanium dioxide to alumina gives a very dense coating that takes an excellent finish. Plasma alumina-titania reaches Rc63, laps to 2 to 4 microinches aa and carries a dielectric strength of 300 volts per mil.

It resists most acids and alkalies and resists wetting by common aqueous solutions, which other ceramics tend to absorb. In one test, unsealed coatings sat in 2% salt solution for five weeks with no sign of penetration to the base metal.

Our nano alumina-titania coating uses the same 13% ratio in nano-sized oxides. It shares the hardness and finish figures and bonds at more than 3,000 psi without a bond coat.

Both grades have a firm ceiling. Above 540°C (1000°F), the coating undergoes a phase transformation that leads to embrittlement and cracking, so they are not candidates for hot service.

Chromium Oxide and Chromium Oxide-Silica

Chromium oxide is the hardest oxide in our range. Plasma chromium oxide is 98% Cr2O3, measures Rc65 to Rc72 and resists abrasive grains, hard surfaces, particle erosion and cavitation below 540°C (1000°F).

It also has excellent self-mating and anti-galling properties. The coating is insoluble in acids, alkalis and alcohol, and when properly sealed it suits corrosive chemical service up to 177 to 205°C (350 to 400°F).

A chromium oxide-silica coating adds 5% silicon dioxide and 3% titanium dioxide. The silica acts as a damping medium that absorbs impact loading and keeps grains from loosening, giving a degree of impact resistance most sprayed ceramics lack.

Petrochemical users apply it to pump impellers, compressor rods, cylinder bores, centrifugal pump seals, wear and casing rings and down hole plungers. It bonds at 4,000 psi without a bond coat and laps to 2 to 4 microinches aa.

Titanium Dioxide

Plasma titanium dioxide is at least 99% TiO2. It forms a hard, dense coating for resistance to abrasive grains and hard surfaces below 540°C (1000°F).

Titania grinds to a very smooth 6 to 8 microinches aa, which suits parts where finish matters as much as wear life. Like other titania-bearing coatings, it embrittles above 540°C.

Zirconia, Titania, Yttria Composite

Hot sections call for a different chemistry. Our zirconia, titania, yttria composite blends 72% zirconium oxide, 18% titanium dioxide and 10% yttrium oxide into a high density coating with both wear and thermal performance.

It keeps its hardness at 1095°C (2000°F), resists air oxidation at that temperature and resists sulfidation and sodium hot corrosion. It also survives air and water quenching from 1095°C, with a maximum surface temperature of 980°C (1800°F) and a thickness limit of 0.050″.

Typical parts include diesel piston rings and crowns, cylinder liners, exhaust valves, valve stems and turbine blades.

Selecting a Ceramic Coating by Property

Start with the failure you are trying to stop, then check the operating temperature. The list below pairs each requirement with the materials built for it.

  • Abrasive wear, erosion and cavitation: chromium oxide for maximum hardness, chromium oxide-silica where impact is also present, premium grade white alumina for smooth, uniform wear surfaces.
  • Fiber and thread wear: white alumina, premium grade white alumina or brush finished chromium oxide, depending on the friction characteristic the process needs.
  • High temperature and thermal barrier: zirconia, titania, yttria composite for hot sections up to its 980°C (1800°F) surface limit; white alumina for thermal barrier duty.
  • Dielectric and electrical insulation: premium grade white alumina at 450 to 500 volts per mil, alumina-titania at 300 volts per mil, or sealed white alumina for insulation at high temperature.
  • Chemical and corrosion resistance: sealed chromium oxide or chromium oxide-silica for corrosive chemical service up to about 205°C (400°F); alumina-titania for resistance to dilute alkalies and aqueous solutions.
  • Finish-critical surfaces: alumina-titania and chromium oxide-silica lapped to 2 to 4 microinches aa, or titanium dioxide ground to 6 to 8 microinches aa.

Temperature narrows the field quickly. Alumina-titania, nano alumina-titania and titanium dioxide all stop at 540°C (1000°F), while the zirconia composite is the choice when the part runs hotter.

Plasma Spray and HVOF for Ceramic and Cermet Coatings

Every oxide ceramic we spray is applied by plasma spray coating. An electric arc ionizes a high flow of inert gas, such as nitrogen and hydrogen or argon and hydrogen or helium. Ceramic powder injected near the nozzle melts and drives onto the part at high velocity.

That heat melts powders with melting points from about 1840°C for alumina-titania to 2535°C for the zirconia composite. The substrate itself stays below 250°F, so the part does not distort and can be steel, other metals, ceramic or even some plastics.

Some jobs are better served by a cermet or carbide than by an oxide. For those, our HVOF coating services apply dense metal and carbide coatings with weld-like bond strength and hardness above HV 1000. HVOF is also a common hard chrome replacement on valves, rolls and landing gear.

Our engineers will tell you which route fits once they see the drawing and the service conditions.

Surface Preparation, Bond Coats and Sealing

Preparation decides how well any ceramic holds. The part is cleaned of surface oxides with a light grit blast, and most oxide grades then need a metallic bond coat before the ceramic goes on.

Two of our materials reduce that step. Nano alumina-titania bonds above 3,000 psi and chromium oxide-silica at 4,000 psi, both without a bond coat.

Thickness is designed in, not added on. Fine-powder ceramics such as white alumina and alumina-titania are limited to roughly 0.020″ to 0.025″, because thicker deposits quickly raise the risk of cracking and delamination.

Sealing closes the remaining porosity. We recommend it for corrosive chemical environments and for white alumina used as a high temperature electrical insulator.

Finishing Ceramic Coatings: Grinding, Lapping and Brushing

Most grades come off the gun at 250 to 550 microinches, with premium grade white alumina far smoother. Working surfaces are then ground, lapped or brushed to size before the part goes back into service.

Ceramic coatings are ground with diamond or silicon carbide wheels, and wet grinding is preferred over dry. Lapping takes alumina-titania and chromium oxide-silica down to 2 to 4 microinches aa, and brushing gives textile parts the controlled texture a thread needs to run over.

A&A handles this work in-house, alongside pre-machining, undercutting and dimensional restoration. Coating and finishing under one roof means one set of tolerances, one schedule and no shipping between vendors.

Industries That Specify Ceramic Thermal Spray Coatings

Oxide coatings show up wherever surface wear, heat or insulation limits component life. Common work at our plant includes:

  • Textile: thread guides and machine elements in contact with fibers and threads.
  • Petrochemical and oil and gas: pump impellers, compressor rods, plungers and seal faces.
  • Pumps and mechanical seals: seal areas coated in premium grade white alumina or chromium oxide.
  • Electronics: components that need dielectric strength from an alumina coating.
  • Diesel engines and turbines: rings, crowns, liners, exhaust valves and turbine blades in the zirconia composite.
  • Printing: plasma sprayed printing rolls for laser engraving.
  • Packaging: sealer bars, jaws and formers protected by our Cerami-Pak coatings for packaging machinery, a ceramic fluorocarbon composite we developed for film and packaging lines.

Ceramic Coating Work Backed by Qualification

For over 70 years, A&A Coatings has worked exclusively in metal, ceramic, cermet and hardfaced coatings. The plant runs seven spray booths, with machining, grinding and lapping on the same floor.

Our quality credentials are specific. A&A is U.S. Navy certified to MIL-STD-1687A, operates a quality system to MIL-I-45208, holds NAVSEA S9320-AM-PRO-030 approval and received a U.S. Department of Defense Achievement Award.

Quotations go out within 24 hours of a complete request, so you can plan an outage or a production run around a firm answer.

Ceramic Thermal Spray Coatings FAQs

Is thermal spray the same as plasma spray?

No, plasma spray is one process within the thermal spray family. Thermal spray also includes metalizing, HVOF and spray and fuse hardfacing, and each suits different materials. When a specification only says thermal spray, the coating material usually decides the process. Oxide ceramics go through plasma spray with the substrate held below 250°F, while carbide and metal coatings often run better by HVOF, and we apply both.

Are industrial ceramic coatings the same as automotive ceramic coatings?

No. Because the same words describe wipe-on car paint products, a drawing or purchase order should name the oxide, such as alumina or chromium oxide, rather than just “ceramic coating.” A sprayed oxide coating is also ground or lapped to a print dimension afterward, something no paint care product is built for. If your search started with vehicle paint protection, this is a different product. If it started with a failing seal, guide or insulator, you are in the right place.

What are the disadvantages of ceramic spray?

The main limits are thickness, temperature and impact, and each one is best settled at the design stage rather than after a part fails. Because most fine-powder oxides stop at about 0.020″ to 0.025″, plan heavy wear as a rebuild to size first, with the ceramic as the final working layer. If the part runs above 540°C (1000°F), rule out titania-bearing grades, and if it takes shock loads, ask about chromium oxide-silica before any other oxide. Chemical service usually adds a sealing step, and finishing calls for diamond or silicon carbide wheels.

What should I send with a request for a ceramic coating quote?

Send a drawing or photo of the part, the base material and the surfaces to be coated. Tell us how the part fails, the operating temperature, any chemicals or electrical requirements, and the final size and finish you need. Our contact form accepts file uploads up to 8 MB. With those details in hand, our engineers can recommend a material and return a quotation within 24 hours.

Can A&A restore a worn part before applying a ceramic coating?

Yes. Salvaging worn and mismachined parts is a core part of our work. We can undercut the part, rebuild lost dimensions with a compatible bond coat or metal coating, then apply the ceramic and grind or lap it to print. Because machining, spraying and finishing happen in one plant, the part moves through every step on a single schedule rather than between separate vendors.

Worn seals, scored shafts and failing insulators? Don’t worry, just trust that A&A Coatings can solve all your needs. Contact Us Today!